Once it loads you into the pit garage before you choose to start your time trial lap, you will be able to assign buttons here. For example just start a Time Trial session, any car and track. You must also make sure that you are in the game (pit garage or on track) and not paused. If that is working smoothly then you could try use the 60Hz option if necessary.į1 2018 / F1 2019: If you are trying to map buttons from your racing wheel to functions in RS Dash, make sure you have RS Dash v2.0m or later as this feature did not work in previous versions. It is recommended that you try a UDP Send Rate of 30Hz in F1 2018 / F1 2019 first with the "Legacy Net Code" option disabled in RS Dash.
F1 2018 PS4 PS4
Verify that your wireless devices are connected using the same Wifi frequency (2.4Ghz or 5Ghz) as your PC / XBox1 / PS4 if that is also connected wirelessly.ĭisable Broadcast Mode and specify the direct IP address of your mobile device (as shown on the RS Dash startup screen once you have selected the game tile)į1 2018 / F1 2019: Please make sure the "Legacy Net Code" option is DISABLED in RS Dash when using the F1 2018 or F1 2019 interface, as it will likely cause lag due to the extra bandwidth used by their protocols. Verify that your device is connected to the same Wifi network as your PC / XBox1 / PS4. F1 2016 / F1 2017 / F1 2018 / F1 2019 - Troubleshooting TipsĮnsure that you have followed the steps above for F1 201x to configure the interface correctly. The steps above for enabling the interface are taken directly from the CodeMasters forum on this topic which you can view here
Hint, the RS Dash application will display the IP address of your device when you have selected an interface.Īfter your changes, your file would look something like (using example device IP of 192.168.100.105) Set the “enabled” value to “true” on the udp0 row enable the telemetry output.Ĭhange the IP address field on the same row to the IP address of your device. In amongst the text (approximately 14 lines down) you should see the tag: Be careful not to change anything other than what is specified below. Right click on the configuration file and choose Open With -> WordPad. \Documents\My Games\F1 2016\hardwaresettings\hardware_settings_config.xml The file is located here ( Note: the configuration file will not exist until you have run the F1 2016 game at least once)
F1 2018 PS4 UPDATE
PC users need to update the game’s configuration XML file to enabler UDP output. If you have problems receiving the telemetry stream with your device, please disable broadcast mode and specify the IP address of your device instead.
F1 2018 PS4 ANDROID
Important: Some android devices may not work correctly with broadcast mode. Hopefully CodeMasters will fix this in a future patch. Important: You will need to do the above steps EACH TIME you restart the game, as it does not save these settings. Note: There is an option called "Broadcast Mode", this may or not work for you depending on a number of factors, so it is recommended that you leave this setting disabled unless you specifically need to run RS Dash on multiple devices at the same time in which case give it a try, if it doesn't work just turn it off again. ( Hint, the RS Dash application will display the IP address of your device when you have selected an interface.) The UDP option will be at the bottom of the list. You will need to turn it on to be able to use RS Dash with F1 2016.Įnabling F1 2016 telemetry output on XBox1 / PS4Įnter the options menu from the main menu (triangle / Y), then enter the settings menu. By default this telemetry output is disabled.
F1 2018 PS4 SIMULATOR
The F1 2016 racing simulator by CodeMasters uses UDP to transmit its telemetry to 3rd party applications such as RS Dash. Note: Please be aware that the game will only start sending telemetry data to the app once you start driving, so prior to that point the app will still indicate that it is waiting for the game to start. If you are experiencing lag with your telemetry or no telemetry at all, please turn OFF broadcast mode and specify the direct IP address of your mobile device instead. Please note though that some Android devices and some wifi routers may have trouble processing the telemetry when "Broadcast Mode" is turned on. It is recommended that you setup a single device first without using broadcast mode to make sure everything is working correctly, then you can give broadcast mode a try.
If you intend to use multiple mobile devices, you will need to set Broadcast Mode to "On".
0 kommentar(er)
